Products
Whytal Wall Putty
Whytal wall putty is a Cement based, water proof wall putty with a blend of polymers and mineral fillers. It can be used in internal and external situation on concrete/ cement plastered walls and ceilings to file the fine pores of the substrate and providing a white, smooth surface required for coating/ painting etc.
Whytal wall putty has good adhesion strength, durability and improves the life of coating/ painting. It does not require curing.
SUBSTRATES
- Concrete
- Plastered walls & ceilings
- Pre- Cast walls
- AAC Blocks
FEATURES
- Smooth finish
- Good bond strength
- Better adhesion moist surface
- Can be applied on moist surface
- No curing required
- Ideal base for paints, distempers and coatings
- Easy mixing and spreading
- For interior and exterior surfaces
PHYSICAL PROPERTIES
| Whytal Wall Putty | @27±, 10 C |
| Pot Life | Approx. 2 hours |
| Wet Density | Approx. 1.80 g/ cc |
| Tensile Adhesion Strength | >1.0N/mm2 @ 28 days |
| Setting time Initial Final | Approx. 280 minutesApprox. 400 minutes |
| Water Absorption Coefficient | <1.0kg/m2 . H1/2 |
| Water Capillary Absorption @ 24hrs | 0.8 ml |
| Water Retentivity | >98.3% |
| White Powder | |
| Initial/final setting time | 270/ 300 min |
| Compressive Strength | 8.5 MP a |
| Flexural strength | 2.1 MP a |
| PH | 9.2 – 10.1 |
COVERAGE ESTIMATES
| Pack Size | Coverage |
| 20kg | Approx. 1.5 – 2.0 m2 /kg (Depending on Wall finish) |
APPLICATION INSTRUCTIONS
Surface Preparation
The cementitious substrate should be made clean and free from dust, dirt & other release agent using wire brush, sand paper, putty blade and clean water. Dry and absorbent surfaces should be pre-wetted with clean water.
Mixing
Mix 20 kg of putty with 7 - 8 litres of clean water to make a smooth paste. Mix thoroughly until a lump-free uniform consistency is achieved. Always mix the quantity which can be used within 2 hours.
Application
Apply the first coat on moistened wall/ceiling surface evenly with the help of flat trowel/putty blade. Allow the coat to dry for 3-4 hours before applying the second coat and allow it to dry completely. After drying of second coat remove marks if any by gentle rubbing with very fine water proof emery paper of not less than 500 number to get a glossy white surface.
Note
Harsh or rough emery papers are not recommended to be used as it breaks the surface film and increases water absorption
STORAGE AND SHELF LIFE
Whytal Wall Putty has a shelf life of 12 months when stored in normal dry conditions.
PRECAUTIONS
Keep out of reach of children. Wear suitable protective clothing, gloves and eyes/face protection. After contact with skin, wash with clean water. In case of contact with eyes rinse immediately with plenty of clean water and seek medical advice.
DISPOSAL/SPILLAGE
Disposal of empty packaging should be in accordance with local waste disposal authority regulations. For further information please refer to the Material Safety Data Sheet.
CONDITION OF SALE
Sold subject to the Company's conditions of sale which are available on request.
NOTE
The information supplied in this datasheet is based upon extensive experience and is given in good faith in order to help you. Our Company policy is one of continuous Research and Development; we therefore reserve the right to update this information at any time without prior notice. We also guarantee the consistent high quality of our products; however as we have no control over site conditions or the execution of the work, we accept no liability for any loss or damage which may arise as a result thereof.
Terms of use | Privacy Policy | Contact us
© 2024 Whytaltech. All Rights Reserved